Carney All Seasons Blog: Posts Tagged ‘Heating’

What is a Gas Furnace Draft Hood?

Monday, December 5th, 2011

As any Maple Glen heating contractor knows, a draft hood is a necessary part of any gas burning appliance. For a gas furnace in particular it ensures steady air flow to the burners to avoid flares or the pilot light being put out by fluctuation in temperature and air flow.

What the Draft Hood Does

The draft will change in the chimney as exhaust vents towards it – especially when going from cold air to hot. A draft hood is placed above the upper most part of the gas furnace to draw air into the chimney and makes it possible to draw more or less air through the chimney as necessary to create a constant flow.

This makes it possible for the burner to enjoy consistent air flow without any wind gusts or sudden temperature spikes or drops. Hot air, if not put through a draft hood would create a strong air flow through the burners.

A draft hood cools the air as it is released by the burners from 500 degrees F to between 300 degrees F and 350 degrees F. The cooling needs to be carefully calibrated to avoid condensation build up in the chimney however – a problem that occurs when the temperature gets too low.

Maintaining Pressure

The draft hood is a part of a larger system designed to maintain air flow to the chimney. For every cubic foot of gas burned, the furnace needs to have 15 cubic feet of air for combustion and another 15 cubic feet of air for dilution. A draft hood and the rest of the ventilation system make it possible to put a furnace that has many thousands of BTUs in the basement of your home and still supply it with enough air to burn gas and dilute the exhaust before it enters the chimney.

For all of these reasons, if you see your pilot light flickering irregularly, notice a backflow of exhaust or a burning smell in your furnace room, it’s important to call a professional heating contractor who can inspect and repair the problem before it becomes any worse. Not only can gas burner exhaust contain high levels of carbon monoxide, it can be bad for the device and the chimney if it doesn’t vent properly.

Continue Reading

Tags: , , , ,
Posted in Heating | Comments Off on What is a Gas Furnace Draft Hood?

Heat Pump Settings and Your Comfort Level

Friday, December 2nd, 2011

Your heat pump has a number of settings that can affect your Fort Washington home’s overall comfort level. One of those settings is the fan – which can be set to run automatically when heating is needed or left on continuously so that the device never turns off. Which is better for your home, though? Let’s take a look.

Comfort vs. Economy

The reason there are two settings on your heat pump is that one is more economical. The auto setting allows the device to minimize how often it is on. So, it only turns on when the house needs warm air to maintain the thermostat setting.

On the other hand, the always on setting is designed to provide better comfort. When you leave your heat pump’s fan on continuously, it provides steady heat over time. This means that the temperature remains consistent and mixes the air to ensure there are no uncomfortable pockets of poorly conditioned air in your home somewhere.

Which Is Better?

In terms of comfort level, it depends on your needs. If you’re not too picky about the exact temperature of your home, the auto setting is best because you will save money and it tends to be fairly accurate. However, if you want to ensure you and your family are perfectly comfortable, regardless of the weather outside, the always on setting is the best way to achieve this level of comfort.

Of course, if you’re concerned about the added cost of leaving the heat pump fan on all the time, you can adjust the thermostat to even out the cost. By raising the thermostat 2 degrees in the summer and lowering it 2 degrees in the winter, the added cost of running it constantly should be offset. If it isn’t, you should have your device inspected to ensure both of the settings are properly calibrated.

Continue Reading

Tags: , , , ,
Posted in Heat Pumps | Comments Off on Heat Pump Settings and Your Comfort Level

Make Your Heating System More Energy Efficient

Wednesday, November 16th, 2011

Efficiency is what you want when it comes to heating your Abington home. You want a furnace that provides the greatest degree of accurate indoor comfort while at the same time operating at peak efficiency to reduce energy usage and lower utility bills. That’s seems like a lot to ask of a simple mechanical system but you should expect it out of the furnace in your basement, attic, or mechanical room.

It is especially important today as energy costs have steadily increased, including electricity, natural and propane gas, and oil. The best way to combat rising prices is to have a furnace that uses less energy. It is a simple statement but one that bears repeating: higher efficiency equals lower operating costs.

Here are some ways to make your heating system more energy efficient:

  1. Clean or replace furnace filters on a regular basis. A dirty or clogged filter will make your furnace work harder and become much less energy efficient. Monthly or quarterly cleaning or replacements are easy to do and will result greater operating efficiencies.
  2. Inspect your home’s ventilation system for accumulation of dirt, dust, or debris. Have you recently added new carpeting? Do your pets shed? Is there a large number of people living in your home? If you answered yes to any of these questions you may need to inspect your ventilation system.
  3. Remove obstructions from around vents and grilles. You need a clean path for air to flow into and out of rooms. Restricted airflow makes your furnace work harder and become less energy efficient.
  4. Consider an upgrade to a two-speed or variable speed furnace. Most older furnaces operated on one speed, which cycled on and off and consumed a lot of energy. Today’s furnaces operate at lower speeds, consuming less energy and often remaining on to keep a steady airflow and prevent constant on and off cycling. These newer furnaces are much more energy efficient and cost less to operate.
  5. Adhere to a regular schedule of planned furnace maintenance. If you don’t clean and inspect your furnace on a regular basis, schedule service calls with a local qualified heating contractor. Your contractor will likely have a service agreement plan to fit your budget, which allows for annual inspections, priority emergency service calls, and discounts on parts and services.

Besides saving on energy costs, your efficient furnace will leave a smaller “carbon footprint.” Your efficient furnace will exhaust less carbon dioxide into the atmosphere and maintain a more “green” profile. And being ecologically friendly can be just as important as saving money.

You can be assured that an energy efficient heating system will keep more money in your pocket this fall and winter.

Continue Reading

Tags: , , , , , ,
Posted in Heating | Comments Off on Make Your Heating System More Energy Efficient

How Often Should I Replace My Furnace Filter?

Wednesday, November 9th, 2011

Just like the filter in your air conditioner, replacing your furnace filter is the key to a healthy and comfortable Willow Grove home. By keeping a good filter replacement schedule, you will reduce wear and tear to the furnace and keep your home warm, while keeping your family healthy and controlling energy costs all winter.

But when does your furnace filter need to be changed? Well, each system is different, but there are some general guidelines and recommendations to follow that can help you keep it all straight and stay on top of your furnace filter situation.

Conventional Wisdom

The long-standing rule of thumb on furnace filters is to change them every month. This is good practice if you are using older fiberglass filters, but for newer, more efficient filters, you should do it a little differently. These should be inspected and cleaned at least once a month, but you may need to replace them that frequently also.

Sometimes it is a little more complicated than these general guidelines, so it pays to be aware of some factors and conditions in your home that may affect how frequently you need to change your filter.

Things to Consider

As mentioned above, the first thing to consider is the efficiency of the filter. Because new filters are so efficient, when they get dirty or clogged with dust and debris, they actually restrict airflow, making your furnace bog down and work harder. So, it is important to stay on top of a monthly inspection and cleaning schedule with these filters.

Also take into account air quality and sources of allergens both inside and outside your home. If you live in an area with a lot of pollutants in the air, you’ll want to replace your filters often to keep those out of your home. If you own a lot of pets, the dander and hair will wind up in your furnace filter and you may have to replace it more often.

Complicated enough for you? It doesn’t have to be. Simplify the whole process by doing the following: check your filter monthly and be prepared to change it that often, clean high-efficiency filters regularly, replace the filter at least every three months and again at the start of heating season.

If you do those things at a minimum, you will be in pretty good shape. If have any questions about furnace maintenance, contact your local contractor.

Continue Reading

Tags: , , , , , , ,
Posted in Heating | Comments Off on How Often Should I Replace My Furnace Filter?

My Furnace isn’t Producing Enough Heat

Friday, November 4th, 2011

If your Telford home is cold, many blame the furnace for not bringing up the warm temperatures or they blame the thermostat for not working right.

It may very well be a thermostat issue – often caused by the location of the thermostat – that is causing the problem. However, sometimes root cause is found in the furnace or ventilation system.

Your indoor environment may be contributing to a seemingly slow-moving furnace. Your furnace may be working too hard to keep up with the heat demand because of an excessive build-up of dirt or debris on the filter or around the moving parts, such as the motor or fan belt. The most obvious thing to do is to keep the airflow unobstructed and keep all working parts clean.

First of all, you should regularly check your furnace filters and if they are dirty, replace them or clean them. Disposable furnace filters are relatively inexpensive and come in a variety of sizes and media ratings (ratings determine what size media is used and its ability to trap certain sized particulate). You can buy these individually or in bulk from a number of different resources. It is a good idea to replace the filters every three-six months.

Mesh filters can be removed, cleaned and reinserted. Like replaceable filters, mesh filters should be checked on a regular basis and then cleaned at least every three months.

You can remove the access panels to your furnace and inspect the components for any build-up of dust, dirt, or debris. Using a vacuum with an extension hose usually is all it takes to clean up the area.

Other reasons for poor heating performance include dirty or blocked ductwork. The harder your furnace has to work to push air through the ventilation system, the longer it takes to bring the heat up. Make your furnace work less and keep vents clear and ductwork clean.

Finally, the reason your furnace isn’t producing enough heat may not be the fault of your furnace at all – you may have a leaky house. But that’s a whole different story.

Continue Reading

Tags: , , , , , ,
Posted in Heating | Comments Off on My Furnace isn’t Producing Enough Heat

Is Your Furnace Making too Much Noise?

Wednesday, November 2nd, 2011

The old saying that “It is better to be seen than heard” certainly applies to the mechanical equipment in your Ambler home. If you hear a squeaky noise or loud clattering you automatically suspect that something is wrong. And if that noise is coming from your furnace, you better pay attention to it. A noise is an obvious sign of a problem – minor or major – and it could result in mechanical failure that could leave your home cold and uncomfortable – and affect your home’s indoor air quality.

Today’s newer variable-speed furnaces keep a constant airflow through the ventilation system utilizing a low speed fan that consumes small amounts of electricity. Constant airflow brings in fresh air and keeps the room air from becoming stale or stagnant. Because of this constant operation, it is important to ensure the furnace is running at peak efficiency, which also means that it is running quietly.

Here are some common noises, possible reasons, and suggested repairs. As always, if you are in doubt about how to repair your furnace, call a local qualified heating contractor and schedule a service call.

  • Squealing noise – could be a worn out or slipping blower belt. Check for proper tension of the belt or replace the belt if it is worn out or cracked.
  • Squealing noise – could be worn out motor shaft bearings. Lubricate the blower motor at the proper points.
  • Rumbling noise – often caused by a poorly adjusted pilot light when the burners are turned off. Adjust the pilot as necessary.
  • Rumbling noise – often caused by dirty gas burners when the burners are switched on. This problem requires service from a qualified heating technician.
  • Buzzing noise – often caused when a blower motor mounting come loose. Tighten the mounting screws or use shims to fill gaps.
  • Hissing noise – indicates a possible air leak. This problem requires service from a qualified heating technician.
  • Ticking noise – possibly a leaky gas valve. This problem requires service from a qualified heating technician.
  • Rattling noise – could be a dirty fan blade. Wipe the fan blade or clean with degreaser.
  • Rattling, grinding, or whining – could be resistance to airflow that causes the motor to work harder. Check the vents in each room for dirt, debris, or obstructions and clear them.
  • Vibrating noise – may not be the furnace but loose or cracked seams in the ventilation system. Check the ductwork seams and hangers to ensure everything is tight. You may need duct tape or bracket hardware.

The best way to keep your furnace and ventilation system from making noises is to practice preventative maintenance. Have your furnace checked annually by a qualified heating contractor – and enjoy the peace and quiet.

Continue Reading

Tags: , , , , , ,
Posted in Heating | Comments Off on Is Your Furnace Making too Much Noise?

How to Get My Furnace Ready for Winter

Wednesday, October 19th, 2011

Being cold in the winter is normal – as long as you are outside. But you shouldn’t be cold inside your New Britain home. If that happens, the first place to look to is your furnace, which may not be working correctly. Furnaces are like any other piece of mechanical equipment. They need to be maintained and serviced on a regular basis to ensure they are working at peak efficiency and warming your entire home at your desired comfort level.

The best time to get your furnace ready for winter is not during the cold winter months – it is before the winter season even begins. There are several way to get your furnace ready for winter and let’s explore some of them.

First of all, check and see when you last had your furnace serviced. If it has been over one year ago, you should schedule and maintenance inspection from your local qualified heating and cooling professional. And when you make that appointment, ask about service agreements and getting on a regular maintenance schedule. Most heating and cooling contractors offer service agreement plans which include furnace and air conditioning check-ups on an annual basis.

Okay, so you know who to call for maintenance but what can you do yourself? First of all, give your furnace a little “help” by checking the vents and returns throughout the house. Ensure that there are no obstructions or blockages such as rugs, clothing, furniture, etc. You need to have unobstructed paths for your heated and return air to flow. The more congested the path, the harder your furnace will have to work. And while you’re at it, make sure your vents are open or closed, depending on how much you use your rooms. For example, if you have an extra bedroom that doesn’t need to be heated, closed off the vent or close the damper in the ductwork. The heated air will be diverted to other parts of your home where it is needed.

You can also help the airflow by vacuuming the vent cover or removing it and vacuuming any of the ductwork that you can easily get to. For a more thorough job consider calling a qualified and professional duct cleaning contractor. Many heating and cooling contractors also offer duct cleaning service, too.

Another maintenance function that you can perform is cleaning or replacing the furnace filter. Depending on the size of your home and its air quality (occupants, pets, etc.), you may want to clean or replace your air filter every one to three months. A dirty filter can restrict airflow and can put contaminants like dirt and dust right back into your air system. If you don’t know how to replace your air filter, consult the furnace owner’s manual or go online to learn more. If your furnace uses an electrostatic air filter, it will need to be removed and cleaned, either by using a hose or with soapy water and a hose. Make sure you let it dry before re-installing it.

You may also want to inspect any electrical wires around your furnace to ensure none are broken or frayed. A visual inspection should be good enough.

Once you have done what you can, let your heating and cooling professional take over from there. They are licensed and trained to inspect your furnace and ensure that it is in peak operating condition. And do it today – while everyone else is waiting.

Continue Reading

Tags: , , , , ,
Posted in Heating | Comments Off on How to Get My Furnace Ready for Winter

What Is a Downflow vs. an Upflow Furnace?

Monday, October 17th, 2011

When you go looking to buy a furnace in Yardley, you may well be surprised by how many different elements go into making a good purchasing decision. There are simply so many different kinds of furnaces available now and they each are more appropriate for certain situations. That means that finding the one that’s right for you is less about finding the one best unit than it is about finding the one that is the best match for your particular circumstances.

This applies to the type of fuel the furnace uses, its energy efficiency, and whether it’s an upflow furnace or a downflow furnace. Energy efficiency and fuel types are probably things that you’re more or less familiar with. But what are we talking about when we classify a furnace as an upflow or downflow model?

Well, it’s pretty much what it sounds like. These terms refer to the direction the air flows as it is taken in and heated by the furnace. So in an upflow furnace, the cool air is taken in at the bottom, warmed, and then expelled at the top. A downflow furnace, on the other hand, takes in cool air at the top and expels heated air at the bottom.

While this is all very exciting, it may still not be obvious what impact this will have on your decision about what type of furnace to buy. The main thing you’ll have to think about when you’re deciding between an upflow and a downflow furnace is where the furnace will be placed in your house.

An upflow furnace is generally installed in the basement so that the heated air is directed towards the parts of the house you want cooled and so that the furnace can be appropriately vented outside of the house. On the other hand, a downflow furnace would be installed in your attic for the same reasons.

So where you want to have the furnace installed is probably the biggest thing to take into account as you’re comparing these two types of equipment. Of course, whether you pick an upflow or a downflow furnace, you’ll still have to select the appropriate AFUE, size and fuel source to best meet your needs. But making the choice between upflow and downflow can at least make it easier to narrow down your options. If you need help choosing the best furnace for your home, contact your local contractor.

Continue Reading

Tags: , , , ,
Posted in Heating | Comments Off on What Is a Downflow vs. an Upflow Furnace?

Safety and Your Furnace

Friday, October 14th, 2011

There are many advantages to a safely operating furnace in your Telford home. The most important are the safety and comfort of a home’s occupants and the cost of running the furnace.  There are several things you can do to ensure the safe operation of your furnace. There are some things you can do to ensure that your furnace runs safely.

Here is a checklist of ideas:

  • Clean or change furnace filters on a regular basis. Replace disposable filters and clean permanent filters using water or cleaning solutions. Your owner’s manual or a qualified heating contractor can suggest a regular maintenance schedule.
  • Check the exhaust vent from the furnace. Clear obstructions such as leaves, clothing, or animal nests from the vent pipe or chimney. Keep roof exhaust vents clear of snow. If there is a faulty exhaust system (like a blocked flue), of if there are cracks and leaks in the pipes or improper adjustment of the burner, or if there is lower air pressure indoors than outside, the furnace can create serious indoor air pollution.
  • A clear air intake is important too, since furnaces need fresh air to “breath” and complete the fuel burning cycle. Again, check for debris, snow, or animal nests in intake pipes.
  • If you have an older gas furnace, you may want to install a supplementary induced-draft fan that reduces the possibility of backdrafting. Some furnaces have automatic shutoff devices that turn off the furnace if it begins to backdraft.
  • Check internal components such as the blower motor and vacuum any dirt. Check belts and pulleys for excessive wear. You should consult your owner’s manual for any suggested maintenance tips on internal working components.
  • You may also want to check the pilot light to see if it is working and if it producing an even, blue flame. If the flame is uneven, it may be a sign of incomplete gas combustion, which can result in the creation of dangerous carbon monoxide gas.
  • Ensure that your thermostat is operating correctly by raising or lowering the temperature settings to make sure the furnace cycles on and off.
  • Install and maintain battery or hard-wired smoke and carbon monoxide detectors.

Externally vented natural gas furnaces, when properly designed and installed, will operate safely for years. But if you detect a problem, use the most common solution – contact a qualified heating professional to check out your furnace.

Continue Reading

Tags: , , , , ,
Posted in Heating | Comments Off on Safety and Your Furnace

Poor Heating Performance with Your Boiler: Possible Causes and Solutions

Wednesday, October 12th, 2011

You don’t have to be a rocket scientist or a mechanical engineer to troubleshoot – and possibly diagnose – the problems with your boiler when its heating performance is erratic or non-existent in your Doylestown home.

The good thing about boilers is that they are typically reliable and long-lasting. There aren’t a lot of working parts that can break down and cause problems, compared to other home heating equipment. When problems do arise, they are usually related to the expansion tank or circulating pumps. But a problem can be much simpler – like a tripped circuit breaker.

The most common problems can be noise, no heat, or poor/erratic heating. Before calling a qualified heating and cooling professional, take a moment to see if you can figure out the what’s wrong.

If you have a noisy boiler it might be because of two things – a faulty circulating pump or water trapped in the return lines. If the pump breaks it will make a loud noise when its motor runs. Water can be trapped in the return lines, which may require “re-pitching” the lines to allow for a flow back to the boiler. You may be able to adjust the flow by positioning hangers on the piping but replacing a pump is better left to a professional.

If your boiler is producing no heat, it could be because of something as simple as a circuit breaker being tripped or a fuse being blown. Check your circuit breakers and fuse and reset or replace if necessary. Is your boiler thermostat in the heat mode? It should be but if it isn’t, make the switch. If your boiler has a standing pilot you should check to see if it is lit and if not, re-light it.

Other problems would take a professional to fix. For example, no heat can be traced to low water levels in the boiler. The boiler should always be half-full of water and if it isn’t, it is likely because of leaks or a faulty pressure reducing valve. Don’t try and fix the problem by yourself.

Low water levels may not cause the boiler to lose its heating capabilities, but may cause fluctuations in its heating capacity. Again, it is advisable to call a professional to diagnose and fix the problem. Poor heating can also be traced to mineral deposits in the boiler. Consult your owner’s manual on instructions how to flush out the boiler.

As always, read the owner guide or operating manual for your boiler. You should get some good tips on proper maintenance and troubleshooting. And have the phone number of a qualified professional taped to your boiler – just in case.

Continue Reading

Tags: , , , ,
Posted in Heating | Comments Off on Poor Heating Performance with Your Boiler: Possible Causes and Solutions